RV Electrical & Battery Systems: Complete Guide
Master your RV electrical system from house batteries to shore power. Covers 12V DC, 120V AC, inverters, and charging.
Results for "shuts off"
737+ Q&A
Updated Daily
Free
RV Water Heater Pilot Light Won't Stay Lit: Thermocouple Troubleshooting Guide
When an RV water heater pilot light won't stay lit after releasing the button, it's usually caused by a faulty thermocouple that needs cleaning or replacement. The thermocouple is a safety device that detects the pilot flame and allows gas to flow.
RV Generator Maintenance & Troubleshooting: Complete Guide
Keep your RV generator running reliably with this comprehensive maintenance and troubleshooting guide for Onan, Generac, and Cummins units.
RV Battery Disconnect Switch Guide: When to Use, What Loses Power & Staying Safe
Guide to RV battery disconnect switches. Covers when to use, what loses power, and best practices for storage and daily use.
Norcold RV Refrigerator Won't Stay On Propane - Complete Troubleshooting Guide
When a Norcold refrigerator starts on propane but shuts off after 1-2 hours, it's typically due to a failing thermocouple, dirty burner, or control board issue. Most problems can be diagnosed by checking the flame appearance and thermocouple connection.
HWH 325 Levelers Shutting Off When Extended? Quick Fix Guide
When HWH 325 levelers turn off immediately after pressing extend buttons, it's typically caused by low voltage under load, loose connections, or a faulty control module. Check battery voltage under load and inspect all connections first.
Atwood AFMD35 Furnace Playing Peek-a-Boo - How to Clean Flame Sensor & Fix Short Cycling
Furnace that lights for 5-10 seconds then shuts off is classic flame sensor failure. Clean the sensor with steel wool or emery cloth - do not use sandpaper. If cleaning fails, replace the sensor. Located near burner, single wire connection.
Suburban SF-42Q Furnace Shuts Off After 5-10 Minutes: Troubleshooting
Furnace running 5-10 minutes then quitting usually indicates overheating from restricted airflow, weak flame, or failing control board. Check combustion air intake, propane pressure, and burner flame quality. Control board becomes suspect if other tests pass.
Why Your RV Generac Diesel Generator Shuts Off After 2 Minutes Under Load: Troubleshooting Guide
Consistent 2-minute shutdown under load indicates fuel delivery cannot keep up with demand. Check fuel pump, bleed system, verify no restrictions. Also check if generator is undersized for AC load - may need soft start on AC unit.
MaxxAir Fan Shuts Off During Shower? Quick Sensor Fix Guide
Your MaxxAir/Fantastic fan is likely experiencing a moisture sensor malfunction or rain sensor false trigger. The fix typically involves checking sensor connections, cleaning contacts, or adjusting sensitivity settings.
Coleman 9420-381 RV Thermostat Voltage Drop: Complete Repair Guide & Solutions
Your Coleman 9420-381 thermostat has failing solid-state switching components causing voltage drop during heating calls. This is a known issue with this model - replace it with a more reliable thermostat or return to a mechanical relay-based unit.
P068A Code Ford V10 RV: Complete ECM Power Relay Control Circuit Fix Guide
P068A indicates an ECM/PCM Power Relay Control Circuit malfunction in your Ford V10. This typically involves a faulty power relay, damaged wiring, or ECM issues causing engine stalling and starting problems.
RV Propane Furnace Clicks But Won't Light - Fix Guide
When your RV propane furnace clicks but won't light, it's usually caused by a dirty or failing igniter, blocked air intake, low propane pressure, or faulty control board. Most issues can be resolved by cleaning the igniter, checking propane supply, and ensuring proper airflow.
Norcold N842IM 'No CO' Error Fix - Complete Propane Troubleshooting Guide
The 'no CO' error on your Norcold N842IM after 8-9 hours on propane is typically caused by combustion issues like a dirty burner, blocked flue, or faulty thermocouple. Start by cleaning the burner assembly and checking for proper ventilation.
How to Fix Onan Generator That Won't Stay Running After Running Out of Gas
After running out of gas, air is in fuel system. Hold start switch longer (15-30 seconds) to purge air. May take several attempts. Check oil level is correct after change.