Results for "tripping"

Turned on my motorhome at 11 PM and it tripped the home GFCI again — works perfectly at campgrounds but I need this solved before departure.

I've tried different adapters, rewired a busted GFCI inside the rig, even turned off ALL the breakers including the main panel breaker. Still trips my house GFCI every time, whether it's the garage, side of house, or front outlets. What gives? Why would it work everywhere else but trip GFCIs at home? There's gotta be something specific causing this, right? …more

Opened my 2022 Holiday Rambler 38N DP and discovered it's eating through surge protectors way faster than normal, despite having the built-in Southwire system. Dealer says I might not need an external surge protector like a Watchdog since it's already built in.

Does a built-in Southwire surge guard provide the same protection as a standalone EMS unit? Should I still install an external surge protector or is the built-in system sufficient? Want to make sure I have proper protection without buying unnecessary equipment. …more

Ripping out my old Suburban water heater to install a Girard tankless but the wiring is completely different — DSI ignition board, different voltage requirements, and the old thermostat wiring doesn't match up. Need a clear wiring diagram for this swap. …more

Nobody expects to find their 2021 Winnebago View 24D transfer switch ground wire completely disconnected at 11 PM when you're supposed to leave tomorrow morning. While replacing a damaged shore power cord, I opened up the transfer switch box and discovered that the main coach power ground wire isn't connected to anything - it looks like it was just cut short with barely any copper showing.

The RV has been this way since we bought it new, and I've never opened this box before. I'm wondering if this could somehow be intentional (maybe related to how the inverter is wired?) or if this is a serious problem that needs fixing right away. Should I be concerned about safety issues, and is this something that typically happens at the factory?

I'd really appreciate some guidance from more experienced folks - I want to make sure I handle this correctly and safely. …more

This Suburban SW6D water heater pilot light keeps going out every single time I try to fire it up. The flame keeps going out after lighting, but only when the access door is closed. When I leave the door open, it stays lit just fine.

This seems like it could be dangerous - I don't want to cause a gas leak or explosion by trying random fixes. Is this likely a combustion air problem or some kind of safety switch issue? I'm hesitant to start taking things apart without knowing what I'm dealing with, but I also don't want to keep running it with the door open if that's unsafe too. …more

Turned down a Class A with a heat pump because I'm terrified of being that neighbor constantly tripping breakers — am I overthinking this? We're plugged into 30-amp service at home while I pretend to know what I'm doing with all these fancy RV features.

Basically, I need to know how many amps this heat pump is going to suck down when it kicks on. I'm already running the usual suspects - fridge, lights, maybe the TV so I can ignore my responsibilities - and I'd rather not find out the hard way that I'm overloading everything. Anyone know the typical amp draw so I can at least look semi-competent when explaining to my spouse why the power keeps cutting out? …more

Looked everywhere for answers but my 2019 Forest River with an Airxcel furnace won't kick on when I switch the thermostat to heat mode. When I turn the thermostat to heat mode and adjust the temperature setting, absolutely nothing happens - no sounds, no fan activation, no ignition attempts, nothing at all. The unit was working perfectly fine last month during our camping trip, but now it's completely dead when I try to activate it through the thermostat.

I've tried adjusting the temperature settings both higher and lower, checked that the thermostat is properly set to heat mode rather than cool or off, and even tried turning the system off and back on again. The thermostat display appears to be functioning normally and shows the temperature settings I'm selecting, but the furnace itself shows no signs of life whatsoever. I'm wondering if this could be an electrical issue, a propane supply problem, or something with the connections between the thermostat and the furnace unit itself. …more

Replaced the DC connections on my Monaco Cayman's Magnum ME2012 inverter per the manual, but I'm still getting 50 amp fault codes and breaker trips. The remote console is consistently showing a 50 amp reading, which I know isn't normal operation. When I watch the unit go through its self-test sequence, it connects initially but then flashes several times before failing completely. The fault light starts flashing on and off intermittently, and eventually the shore power breaker trips entirely.

What's really concerning is that my batteries aren't charging at all during this process. I've read through the manual and it mentions that the inverter might need a reset to clear fault conditions, but I'm not sure if that's the right approach here or if there's something more serious going on. The combination of the 50A fault display, failed self-test, and the shore power breaker tripping makes me think this could be a significant electrical problem.

What steps should I take to diagnose whether this is a simple reset issue or if my ME2012 inverter has a more serious internal problem that needs professional attention? …more

Got my 2021 Winnebago View 24D torn apart right now and there's charred components scattered all over the inside of this completely dead Xantrex inverter. Rather than replace with another Xantrex unit, I'm considering upgrading to a Victron MultiPlus system.

The RV is equipped with dual 100Ah LiFePO4 batteries and 200W solar array. Current electrical configuration uses the standard Winnebago 12V DC system with 30A shore power connection. The failed Xantrex unit was a 2000W inverter/charger combo with remote panel monitoring.

Which specific Victron MultiPlus model would provide optimal performance for this application? Additionally, what connection modifications will be required, and can the existing Xantrex remote panel be eliminated in favor of app-based monitoring? …more

About to crawl under my 1995 Thor Mirage RV's dashboard staring at endless wires and components with no clue which one is the Ford F53 460 inertia switch. I have a 1995 Thor Mirage Class A with the F53 chassis and 460 engine. After hitting a pretty good bump on the road, my fuel pump stopped working completely.

I've been reading online and it sounds like the inertia switch probably got triggered, but I'm having trouble figuring out exactly where it's located on my rig. I've seen some posts mentioning the steering column, but I've looked there and can't find anything. Could someone help me understand where I should be looking for this switch and what it actually looks like? I'd really appreciate any guidance from someone who's dealt with this before. …more

During these scorching summer days, this complete RV newbie is baffled why my Class A's GFCI keeps tripping every few days and I'm totally lost. The RV isn't plugged directly into the GFCI outlet, but there's one on the same circuit that keeps popping.

I'm wondering if my solar inverter might be the culprit since it seems heat-related? Or could this be pointing to a battery that's starting to go bad? Just trying to figure out if this is normal wear and tear or something I need to address before it gets worse. …more