Results for "body mounts"

According to three different RV shops, fixing my bubbling sidewall delamination will cost thousands, but I'm wondering if tackling this DIY repair myself is actually feasible. My 2004 Itasca Sunova has decided to sprout some lovely blisters on the right sidewall - two beauties that are about 12-14 inches long and 3-4 inches wide, running vertically right behind the awning arm. Perfect timing since we're currently on the road living our best RV life!

I'm pretty sure water snuck in somewhere (probably from the roof rail or that shower skylight we never use), and now my RV looks like it's got chicken pox. Since we can't exactly pull into the nearest RV surgeon's office, I need to know: what can I do right now to stop this from getting worse, and what's involved in actually fixing this mess properly? I'm hoping there's some kind of emergency containment plan that doesn't involve duct tape and prayers! …more

Nobody warned me that what started as minor swaying on highway trips last month would turn into white-knuckle driving every time I take my F53 chassis RV over 50mph. SDI E-Clik costs about a third of what Liquid Spring systems run, but I'm wondering what you actually get for that price difference.

Is E-Clik just electronic shock control, or does it offer more comprehensive suspension improvements? How does the ride quality compare between the two systems on F53 motorhomes? …more

Hearing a loud cracking or popping noise from underneath my Dutchstar when going over bumps or turning. Sounds structural — like metal flexing or a weld breaking. Crawled under and couldn't see any obvious cracks but the noise is getting louder each trip. …more

Spent all morning staring at my new Tiffin Allegro 33AA trying to figure out how to mount a telescopic flag pole without destroying something. My previous RV had a fixed ladder which made mounting easy and secure, but this new rig doesn't have that option.

I'm concerned about using suction cups or zip ties because they don't seem very secure, and I'm afraid the telescopic flag pole could come loose while driving and cause damage or become a road hazard. The bike rack is already occupied with our bikes, so that's not available either.

What are some safe, secure mounting options that won't damage the RV's exterior? I need something that will hold firmly during highway speeds but won't leave permanent marks or holes in my new rig. …more

Somewhere between our freezing mountain trip last month and now, my 2002 Born Free's SF-30 furnace died completely and I'm torn between replacing the core versus the whole unit. I believe it's a Suburban SF-30 model. I've been doing some research and see there are two options - I can buy a complete furnace replacement or just get a replacement core that supposedly slides into the existing SF-30 housing for about half the price.

I'm honestly not sure which route to go. The cost savings on the core is tempting, but I don't want to make the wrong choice and end up with more problems. As someone who's still learning about RV maintenance, would you recommend getting the complete unit or would the core replacement work just as well? Any guidance would be really appreciated! …more

Our Ford E-450's front suspension is making grinding noises when I turn - is this dangerous with kids in our Winnebago? My 2007 Winnebago Outlook 31' has been driving like absolute garbage and everyone keeps mentioning this "quick fix" for Ford E-450 chassis front suspension issues. I've been crawling under this thing for hours trying to figure out what I'm even looking at.

I keep hearing about track bars, radius arms, coil springs - but honestly, I can't tell which is which on my setup. The suspension doesn't look like the simple diagrams I've seen online. Can someone please break down exactly what components are involved in this quick fix for the E-450 chassis? I really need to know what I'm dealing with before I make this worse than it already is.

I'm willing to take photos and get help from other owners if needed, but first I need to understand what parts I should even be focusing on. This motorhome has been my home and I desperately need to get this sorted out! …more

Looked everywhere and my F-53 chassis is still showing 2.1 inches of body roll with quad shocks installed, but forums claim it should be under 1 inch. As a former high school auto mechanics instructor with 35 years of experience, I've carefully considered the shock design challenges in RV suspension.

I installed additional shocks after discovering that shock suppliers list a single shock design for F-53 chassis ranging from 16,000 to 26,000 lbs. I used Koni shocks ($170 each) and supplemented with Monroe shocks ($75 each) for additional dampening.

Installation required 10" bottom bolts and modified top mounting. I used hardened washers to prevent shock cover contact. Total bolt modification cost was approximately $18.

Completed a 30-mile test drive with no apparent harshness or negative handling characteristics. The suspension feels more controlled during normal driving conditions, but this limited test may not reveal the full performance picture.

What's the recommended approach for thoroughly evaluating quad shock performance on the F-53 platform? Specifically looking for guidance on testing duration, road conditions to assess, and key performance indicators to monitor during the break-in period. …more

Staring at my 1995 Ford F53 motorhome's rear sway bar bushings that look perfectly fine, probably a dumb question but why does this thing sway like crazy over every bump? I can hear some clunking back there and the handling feels loose and wallowy.

I'm planning to tackle this myself (because apparently I enjoy spending my weekends cursing at rusty bolts). When replacing these axle bushings, be extremely careful with bolt alignment. The nuts are welded to the bracket, and if you don't align everything precisely, you risk cross-threading, which can turn a simple job into a much longer project - I learned this the hard way and had to chisel off a nut.

I've got some photos documenting my process and can share those if anyone's interested. I did not need to replace the upper sway bar tie rod bushings this time. Should I stick with the original rubber ones or is it worth upgrading to something better? And since I'll already be crawling around under there getting dirty, are there any other components I should check or replace while everything's accessible? …more

Somewhere between my third passenger-side drop of 1.5 inches this season on my 2021 Jayco Alante, I'm officially done with the guessing games on this lean. I've checked and it's not because of full tanks or uneven loading. When I had it looked at, they said the frame and suspension are square and level, so that's not the problem.

I'm thinking it might be something with the body mounts? Could this be loose bolts or worn rubber parts? I've heard about body shims but not sure if that's the right fix. Since it's still pretty new, would this be something covered under warranty? Any guidance would be really helpful - I want to make sure I'm approaching this the right way. …more

The third time this season my F-53 motorhome has been rocking like a boat at campgrounds and I'm done pretending the SDI E-Clik stabilizer system isn't worth investigating. The body roll on highway drives has me white-knuckling the steering wheel, and I'm worried about safety for my family.

I keep seeing mixed information online - some people seem to love it, others say it's just marketing hype. I don't want to throw money at a problem that needs a more serious suspension overhaul, but I also can't afford a complete suspension replacement right now.

Can anyone share honest, real-world experiences with the E-Clik system? Does it actually improve handling enough to notice, or am I setting myself up for disappointment? I need realistic expectations before I commit to this purchase. …more

I turned the black tank valve handle on my 2023 Montana 3793RD and it's just spinning freely without actually opening the valve mechanism. Need to locate the actual gate valve to check the connection. Where exactly is this valve positioned on this model? Do I need to access it through the underbelly panels? …more